FIRST Robotics Competition

The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been carefully optimized to provide torque density unavailable in FRC up until now. The...

For use with the ION Build System 1in Extrusion to create linear motion.   Kit Contents QTY 1 - REV-21-1032 - Dual Bearing Plate QTY 1 - REV-21-1029 - Eccentric Bushing QTY 1 - REV-21-1030 - Concentric Bushing QTY 2 -...

The 3/4in Needle Bearing Carrier is compatible with the REV ION System and designed for use with the Needle Bearing - 3/4in ID to turn MAXSpline Shaft extrusion into a dead axle roller. Specifications Material: Glass-Filled Nylon...

The 3/4in External Retaining Ring is compatible with the REV ION System and is used to constrain movement on the Dead Axle Tube - 3/4in for intake and roller applications. Specifications Material: Steel Documentation ION Build System...

The 2 Motor Drivetrain Gearbox - Through Bore is compatible with the REV ION System and can be mounted in a variety of options, including flush with tube or spaced away from the tube to enable both chain in tube and chain/belt outside tube designs...

The 4in EasySwerve Drivetrain Kit with NEO Vortex motors is a complete solution for building a high-performance REV ION drivetrain base, combining the control of swerve with the flexibility of MAXTube. It includes four 4in EasySwerve Modules powered by...

The 4in EasySwerve Drivetrain Kit with NEO 2.0 motors is a complete solution for building a compact and capable REV ION drivetrain base, combining the control of swerve with the flexibility of MAXTube. It includes four 4in EasySwerve Modules powered by...

The ION Bearing Bundle brings together the most-used bearings and bearing blocks in the ION Build System so you can spend less time sourcing parts and more time building. From high-speed shooters to rugged drivetrains to MAXSpline-based arms and pivots,...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION...

Upgrade your 3in MAXSwerve Module with this high-performance motor and controller package, featuring the latest NEO Vortex Brushless Motor and SPARK Flex Motor Controllers. Created for maximum efficiency and advanced control, this bundle is perfect for...

Power your 3in MAXSwerve Module with this proven motor and controller setup, featuring the NEO Brushless Motor and SPARK MAX Motor Controllers. Designed to work seamlessly with the 3in MAXSwerve Module, this bundle delivers reliable performance and...

The Bearing Retaining Plate is compatible with the REV ION System and is designed to securely hold bearings in place, ensuring that they remain stable and aligned during use. Made from high-quality, durable materials, the Bearing...

Ratio Plates are compatible with the REV ION System. When you need a ratio other than 1:1, Ratio Plates make it easy to position sprockets and pulleys at the perfect center-to-center distance for the given ratio and length of #25 chain or RT25 belt...

This 4-pin JST PH to 4-pin roboRIO I2C Cable is designed to connect REV I2C sensors, like the REV Color Sensor V3, to the I2C port on the NI roboRIO for use in the FIRST Robotics Competition. Each cable is approximately 36 inches long. This cable...

The JST PH 6-pin to 4 Channel PWM Cable allows for seamless connection of the Through Bore Encoder into the FRC control system (roboRIO).

1in Extrusion is compatible with the REV ION System. It’s a 1in x 1in square extruded aluminum tube, with slots designed to fit standard #10 hardware rather than expensive t-nuts. Take your robot mechanisms to a new level of sleekness with the Black...

These SPARK PWM Cables have a JST-PH 4-pin connector on one end, and a 0.1in 3-pin female PWM connector on the other. They are designed to convert the SPARK MAX Motor Controller's PWM/CAN port to a standard 3-pin PWM port on a robot controller. The black...

This Eye-to-Eye Turnbuckle is ideal for tensioning string, cordage, or cabling in linear motion applications. The welded eyes provide significantly more strength than bent eyes. Specifications Material: Steel Thread: M5 Retracted Length: 106mm +-...

Split Lock washer with a 3/8in inner diameter. Specifications Material: Zinc-plated Steel ID: 3/8in OD: 0.680in Thickness: 0.094in Documentation ION Build System Guide #10 Hardware Basics CAD & Drawings REV-29-1240 Drawing

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1-1/2in Documentation ION...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length includes the flat screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION Build System...

The 1in Inside Corner Bracket is designed to enable more construction strategies with the 1in Extrusion. Designed for #10 hardware, the mounting holes are on a 1in pitch that allows for the creation of complex joints by stacking with other 1in...

The 1in Extrusion Endcap Slide allows teams to create compact and robust multistage lifts when combined with the 1in Linear Motion Kit (REV-15-1189) and the 1in Extrusion (REV-21-1000). The slide tab is offset allowing stages to fully nest when collapsed...

The REV POE Injector Cable was specifically designed to address a common problem for many FRC teams with their wireless radios: intermittent power glitches. The wireless radios used in the last several FRC seasons can be powered either through a...

This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED. Each color can be controlled separately to create any...

Extend the reach of your MXP port by using this 18" cable to reposition your boards where you need them. Fully compatible with all REV Robotics MXP accessory boards (More Board, Proto Board, & RIOduino) Specifications Keyed male and female...

The REV Robotics Digit is multi-use MXP board for interface with the roboRIO. It has four 12 segment displays, which can be used to show any letters or numbers. It also features an analog potentiometer and two momentary buttons. Teams can use the...

Eccentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. The hole is drilled off-center of the bearing axis so by rotating the bushing on its mounting bolt, the clearance between the wheel and track can...

This dual bearing plate holds two V-Groove Bearings (REV-29-1014) to create an easy linear motion system for the ION Build System 1in Extrusion (REV-21-1000). Using a combination of Concentric (REV-21-1030) and Eccentric (REV-21-1029) bushings, the user...

Concentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. Used in conjunction with our Eccentric Bushing (REV-21-1029), the user can adjust how tight or loose they would like to tune their linear...

REV Polycarbonate Sheets are lightweight, clear, and impact-resistant plastic sheets for robot construction, prototyping, covers, guards, sponsor panels, intake surfaces, funnels, and other custom mechanisms. Polycarbonate is durable while still allowing...

The JST PH 6-pin Joiner Boards (REV-11-1277-PK4)  are intended to be used with the JST PH 6-pin Extension Cables to extend the reach of your NEO Brushless Motor sensor cables. The JST VH 2-pin Joiner Board - 4 Pack (REV-31-1429-PK4) are small...

The SPARK Flex Data Port Breakout Cable (REV-11-2853) breaks out the default pin functions of the SPARK Flex Data Port into commonly used connectors for external sensors. The keyed and locking Data Port connector ensures a secure and aligned fit when...

The USB-A to USB-C 2.0 Cable - 2m (REV-11-1232) is a longer version of the USB-A to USB-C cable included with the SPARK MAX Motor Controller and the Control Hub. Use this cable to connect your SPARK MAX or Control Hub to a standard computer from up to 2...

1.2mm UHMWPE Cord - 10M (REV-41-1162) is a high strength string for use with the small Pulley Bearings and the 15mm Linear Motion Kit to create a powered lift.   3mm UHMWPE Cord - 10m (REV-29-1244) is a high-strength and low-stretch...

Absolute Encoder Adapter (REV-11-3326) connects the REV Through Bore Encoder directly to the SPARK MAX Data Port. This adapter connects the Absolute Duty Cycle output of the Through Bore Encoder to the correct SPARK MAX Data Port pins while leaving the...

The 36in PWM Cable - 4 Pack (REV-11-1130-PK4) is an ideal servo extension, providing a 3ft reach for servos, sensors, and other PWM-controlled devices. Featuring a universal 3-pin design with a female connector on one end and a male connector on the...

These spare parts are designed specifically for the 4in EasySwerve Module (REV-21-3006). These replacement base plate and cover components make servicing and maintenance simple. Routine replacement of worn or damaged parts helps preserve performance,...

Complete gear set replacement for the Smart Robot Servo V2. Documentation Smart Robot Servo V2 Overview Smart Robot Servo V2 - Balanced Gear Replacement Guide

Nylon Zip Ties with rounded edges to prevent snagging. Length is idea for cable management and many other uses. Specifications 160mm long Quality nylon construction 18lb. tensile strength