Competition

Connecting link for #25 chain. Use a connecting link to connect two ends of chain to create a loop. Specifications Material: Steel Size: #25 Pitch: 0.25in CAD & Drawings REV-41-1366 STEP File REV-41-1366 Onshape

This #25 roller chain is designed for use with #25 sprockets. Each package includes 1 connecting link, and additional links are available separately in the #25 Connecting Links – 5 Pack. For custom chain lengths, we recommend the REV #25 Chain...

Replacement battery for the Driver Hub (REV-31-1596). Specifications 5040 mAH Li-ion battery  Documentation Driver Hub User's Manual Driver Hub Getting Started Guide

This sensor can be used to read and compare colors, and also has a built-in IR (optical) Proximity Sensor and white LED for active target lighting. Supports High Speed I2C Communication (400kHz) as well as auto increment register read which allows the...

The REV Robotics 2m Distance Sensor uses the ST Microelectronics VL53L0X Time-of-Flight (ToF) laser-ranging module to measure distances up to 2 meters with millimeter resolution. Unlike other ranging sensors that rely on the intensity of reflected light,...

The REV Robotics Magnetic Limit Switch is a three-sided active-low digital hall effect switch with three internal hall effect elements located on the top and sides of the sensor. The three elements are connected in parallel so that any one of them will...

Easily connect multiple devices to your robot battery with the XT30 Power Distribution Block. Allows for clean, compact wiring of all your XT30-connected devices. Compatible with: Expansion Hub, Blinkin LED Driver, SPARKmini, Servo Power Module, and many...

The 3in MAXSwerve Aluminum Wheel was designed for the 3in MAXSwerve Module. You can attach your favorite tread material to this wheel. REV recommends rough top conveyor belting. A cut template for the wheel tread is available below...

The 2 Motor Drivetrain Gearbox - Through Bore Bundle contains the REV-21-2190 base kit, the 20DP Gears needed for a 6in wheel ratio, and 20DP NEO Pinions Gears (10T, 11T, 12T) for multiple speed options. If a 4in or 5in wheel gear ratio is needed,...

The #25 Chain Turnbuckle is compatible with both the REV ION System and REV DUO System. It is designed to adjust the length of a #25 Chain by replacing a few links in a run and also allows the user to tension the chain by adjusting the...

These JST PH 6-pin Extension Cables are intended to extend the reach of sensor cables without having to cut and splice wires. Specifications Length: 30cm Notes As of 01/10/2024, the length on this product page has been corrected from 15cm to 30cm...

The 3in MAXSwerve Module Wheel Hardware Pack was designed for the 3in MAXSwerve Module. This kit is for FRC teams looking to streamline their wheel maintenance at competitions. With this kit, teams can pre-build their wheel assemblies, making...

Connect the REV Through Bore Encoder directly to the SPARK MAX Data Port using this adapter. This adapter connects the Absolute Duty Cycle output of the Through Bore Encoder to the correct SPARK MAX Data Port pins, leaving the incremental quadrature...

This product is a 6:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 5:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 3:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 2:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 1:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

New and improved, the Mecanum Drivetrain Kit V2 gives teams all the parts needed to build a Mecanum Drivetrain for use within robotics programs like FTC. This updated kit uses Ultra 90 Degree Gearboxes to place the UltraPlanetary HD Hex Motors within the...

The MK Battery ES17-12 is commonly used in FIRST Robotics Competition robots. Specifications Manufacturer: MK Battery Voltage: 12V Capacity: 18AH (20 Hour Rate) Product Dimensions: 7.13in x 2.99in x 6.57in Weight: 12.89lbs Documentation MK...

Dead Axle Tube is compatible with the REV ION System and can be used with 3/4in Needle Bearing Carrier (REV-21-2385) and MAXSpline Shaft (REV-21-2520) as the dead axle in a dead axle roller. Can also be used with custom rollers and as...

The 1in Pivot Joint is compatible with the REV ION System. Create a pivot joint at the end of a piece of MAXTube - 1x1 with Grid Structure. Specifications Material: POM (Acetal/Delrin) Documentation REV ION Build System Documentation Introduction...

The MAXSpline Shaft is compatible with the REV ION System. The shaft is an extruded aluminum MAXSpline that provides a high strength alternative to 1/2in hex shaft that can interface with any REV ION System components with a MAXSpline bore. The...

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0...

The WAGO 221 Inline Splicing Connector is a robust and easy to use splicing connector that makes fiddling with hard-to-master crimp-style connectors a thing of the past. Simply lift the lever up, insert the stripped wire, and push the lever back down to...

The REV Mini Power Module (MPM) is a compact power distribution module that allows you to securely and quickly power peripheral devices to your robot. Need more low-current channels on your PDH? Wire the MPM to one of the high-current channels on the PDH...

The MAXPlanetary 550 Input Kit gives users the ability to use 550 size motors with the MAXPlanetary System.  Features Does not require permanent modifications to the motor Press-fit shaft adapter avoids set screws that can come...

The MAXPlanetary 775 Input Kit gives users the ability to use 775 size motors (775pro or AM RedLine) with the MAXPlanetary System. Features Does not require permanent modifications to the motor Press-fit shaft adapter avoids set screws that...

The REV Driver Hub is a compact mobile computing device designed for interfacing with the Control Hub (REV-31-1595). The Driver Hub was designed and built as an easy to use, dependable, and durable device for use in classroom and the competition. It...

With over 180 parts, the EDU Kit V2 is specifically created to implement hands-on STEM projects in the classroom. This robotics kit is used to teach a variety of lessons ranging from computer programming and engineering principles to project management...

The M3 Hardware Bundle provides a multitude of hardware options that can be used within the 15mm Build System. The focus of the bundle is on compatibility with structural components like Extrusion and Brackets. Use this bundle to restock your...

The FTC Timing Belt and Pulley Bundle contains an assortment of components needed for a pulley-based motion transmission system. Timing Belts and Pulleys are lighter, more compact, and more efficient at transferring motion than chain and sprockets...

The 5mm Hex Shaft and Spacer Bundle features an assortment of REV products that work to transmit intended motion and constrain unintended motion in the DUO Build System. Use this bundle to restock your existing shaft and spacer supply, or as a great...

The FTC Cable Bundle offers a plethora of major cables and other accessories for a variety of robot design needs, without having to sacrifice wiring best practices. Necessary cables, like the XT30 Extension Cable, come in two different...

The M3 Standoff Bundle is perfect for raising one assembly above another or as linkages. Standoffs are also commonly used with REV C Channel to properly space the channel in order to allow chains or belts to fit inside. Use this bundle to...

The FTC Bearing Bundle offers a plethora of motion support components for the 15mm Build System. The basics of motion support can be found on the Supporting Motion documentation page. Use this bundle to restock your existing bearing supply, or as a...

The C Channel Bundle contains various lengths of 45mm x 15mm C Channel and is designed to work seamlessly with existing REV 15mm Extrusion. They can be used in locations where additional torsional strength is required. The 45mm wide side...

The U Channel Bundle contains multiple lengths of 45mm U Channel and is designed to work seamlessly with existing REV 15mm Extrusion. The U Channel Endcap and Tensioning Bushing allows users to fine tune their system when designing and...

The Servo Bundle is a one stop shop for getting up and running with the REV Smart Robot Servo. Included in this bundle are all the major electronic and structural accessories for programming, powering, and building using the Smart Robot Servo. Use...

The #25 Chain and Metal Sprocket Bundle can be used to change the speed, torque or direction of a motor. The REV 15mm Build System is designed around #25 Roller Chain using compatible #25 Sprockets. The bundle also includes the...