Shop All

1/2in Rounded Hex Shafts are compatible with the REV ION System and are a ready-to-use length of hex shaft that have been cut to length and have the ends tapped. The ends are tapped #10-32 in order to accept a screw and washer or shaft collar. The 1/2in...

#10-32 Standoffs are compatible with the REV ION System and provide spacing for mounting key items on your robot. These standoffs are tapped on each end for a #10-32 thread and have a 3/8in flat to flat dimension, similar to a #10-32 nut. Specifications ...

The REV Radio Power Module is designed to keep one of the most critical system components, the OpenMesh OM5P-AC WiFi radio, powered in the toughest moments of the competition. Traditional barrel jacks easily work themselves loose and often require hacks...

Experience a significantly longer lifespan with the 3in MAXSwerve Plastic Wheel V2.0, designed for the 3in MAXSwerve Module. Now crafted from Glass-Filled Polypropylene & TPR, it boasts a more rigid rubber tread for increased durability without...

An individual cartridge for the MAXPlanetary System. This cartridge is a 5:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

An individual cartridge for the MAXPlanetary System. This cartridge is a 4:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

An individual cartridge for the MAXPlanetary System. This cartridge is a 3:1 gear reduction. The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been...

The MAXPlanetary System is a cartridge-based modular planetary gearbox designed from the ground up for NEO-class motors. The design of the MAXPlanetary has been carefully optimized to provide torque density unavailable in FRC up until now. The...

For use with the ION Build System 1in Extrusion to create linear motion.   Kit Contents QTY 1 - REV-21-1032 - Dual Bearing Plate QTY 1 - REV-21-1029 - Eccentric Bushing QTY 1 - REV-21-1030 - Concentric Bushing QTY 2 -...

The 3/4in Needle Bearing Carrier is compatible with the REV ION System and designed for use with the Needle Bearing - 3/4in ID to turn MAXSpline Shaft extrusion into a dead axle roller. Specifications Material: Glass-Filled Nylon...

The 3/4in External Retaining Ring is compatible with the REV ION System and is used to constrain movement on the Dead Axle Tube - 3/4in for intake and roller applications. Specifications Material: Steel Documentation ION Build System...

The USB Female A to Micro USB Adapter allows you to use standard USB devices with micro 5-pin oriented electronics. Use this cable adapter to connect a Robot Controller phone to an Expansion Hub, or to connect a Driver's Station phone to a single...

The 5.5mm WERA Socket Screw Driver is for use with M3 hex head screws and nuts. Kraftform Ergonomic Micro handle design features the shape that facilitates high torque transfer and precision feel for fine adjustment work,...

Tote around your extra robot parts with the classic REV Storage Tote. This is the same tote included with the EDU Kit V2 and the FTC Starter Kit V3.1 as well as previous versions. Specifications Color: Orange External: Length: 554mm (21.81in) Width:...

The 2 Motor Drivetrain Gearbox - Through Bore is compatible with the REV ION System and can be mounted in a variety of options, including flush with tube or spaced away from the tube to enable both chain in tube and chain/belt outside tube designs...

The 4in EasySwerve Drivetrain Kit with NEO Vortex motors is a complete solution for building a high-performance REV ION drivetrain base, combining the control of swerve with the flexibility of MAXTube. It includes four 4in EasySwerve Modules powered by...

The 4in EasySwerve Drivetrain Kit with NEO 2.0 motors is a complete solution for building a compact and capable REV ION drivetrain base, combining the control of swerve with the flexibility of MAXTube. It includes four 4in EasySwerve Modules powered by...

The ION Bearing Bundle brings together the most-used bearings and bearing blocks in the ION Build System so you can spend less time sourcing parts and more time building. From high-speed shooters to rugged drivetrains to MAXSpline-based arms and pivots,...

REV 45mm U Channel has a 45mm x 45mm square profile, and is designed to work seamlessly with existing REV 15mm Extrusion. It can be used in locations where additional torsion strength is required. On the sides of the channel is the Extended Motion...

The UltraUSB Hub is designed specifically for use in competitive robotics, and gives you the ability to connect multiple USB devices to each other as well as replacing cables when damaged instead of needing to replace the whole hub. The UltraUSB Hub can...

This bearing pillow block bracket (REV-41-1317) is used with the DUO Build System 15mm Extrusion. The 9mm center hole is use with either the Long Through-bore Bearing (REV-41-1329) or the End Cap Bearing (REV-41-1322) to provide a low friction shaft...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION...

Upgrade your 3in MAXSwerve Module with this high-performance motor and controller package, featuring the latest NEO Vortex Brushless Motor and SPARK Flex Motor Controllers. Created for maximum efficiency and advanced control, this bundle is perfect for...

Our official REV Sticker Bundles are designed for teams, educators, and event organizers. Sold in bulk quantities of 100, perfect for gear trading and giveaways. Whether you’re decking out a new robot fleet or prepping for a regional event, these bundles...

Power your 3in MAXSwerve Module with this proven motor and controller setup, featuring the NEO Brushless Motor and SPARK MAX Motor Controllers. Designed to work seamlessly with the 3in MAXSwerve Module, this bundle delivers reliable performance and...

This product is a pack of 10 Tooth pinion gears for the 2 Motor Drivetrain Gearbox - Through Bore. Purchasing a Base Kit, Gear Ratio, and Speed Option are all required to assemble a full gearbox, visit the 2 Motor Drivetrain Gearbox - Through...

This product is a 6in Wheel Gear Ratio for the 2 Motor Drivetrain Gearbox - Through Bore. Purchasing a Base Kit, Gear Ratio, and Speed Option are all required to assemble a full gearbox, visit the 2 Motor Drivetrain Gearbox - Through Bore...

This product is a 5in Wheel Gear Ratio for the 2 Motor Drivetrain Gearbox - Through Bore. Purchasing a Base Kit, Gear Ratio, and Speed Option are all required to assemble a full gearbox, visit the 2 Motor Drivetrain Gearbox - Through Bore...

This product is a 4in Wheel Gear Ratio for the 2 Motor Drivetrain Gearbox - Through Bore. Purchasing a Base Kit, Gear Ratio, and Speed Option are all required to assemble a full gearbox, visit the 2 Motor Drivetrain Gearbox - Through Bore...

The Bearing Retaining Plate is compatible with the REV ION System and is designed to securely hold bearings in place, ensuring that they remain stable and aligned during use. Made from high-quality, durable materials, the Bearing...

M3 Spacers are compatible with the REV DUO System and accurate way to space gears, sprockets, wheels, and other parts on a M3 bolt.  

Washer for use with REV DUO M3 hardware.

M3 Ball Joint Rod Ends are compatible with the REV DUO System. The Female M3 Ball Joint Rod End (REV-49-1560) can either be paired with its male counterpart to create short linkage arms or with M3 threaded rod and a second female ball...

5mm Metal Hex Bore Gears are compatible with the REV DUO System and work with REV 5mm hex shafts in high-load applications. REV metal gears are NOT compatible with REV plastic gears. All REV metal gears are narrower than plastic...

5mm Plastic Hex Bore Gears are compatible with the REV DUO System and fit on a 5mm hex shaft. The hex shaft interface completely eliminates the need for expensive hubs or using potentially unreliable set screws. Gears 45 tooth...

15mm Plastic Motion Brackets are compatible with the REV DUO System. Each bracket features a set of alignment ribs designed to seat the bracket into the extrusion channel increasing joint alignment, strength, and rigidity.  The 15mm Plastic...

DUO L Beams are compatible with the REV DUO System and are a structural element for small load applications or as a supporting component on a larger load application. They are compact, lightweight, and provide more strength than a flat beam. Use them to...

DUO Flat Beams are compatible with the REV DUO System and are easy to use. Having an 8mm width, 3mm height, and 8mm hole pattern makes them perfect as a support for an upright or using them as a linkage.  Specifications Material: 6063...

Ratio Plates are compatible with the REV ION System. When you need a ratio other than 1:1, Ratio Plates make it easy to position sprockets and pulleys at the perfect center-to-center distance for the given ratio and length of #25 chain or RT25 belt...

This Motion Pattern Spacer offers a convenient and accurate way to space gears, sprockets, wheels, and other parts through the Motion Pattern interface. Great for getting the proper spacing when face mounting to the UltraPlanetary Gearbox...