Shop All

This product is a 6:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 5:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 3:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 2:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

This product is a 1:1 Ratio Gear Bundle for the 2 Motor Gearbox - Through Bore. Purchasing a Base Kit and Ratio Gear Bundle are both required to assemble a full gearbox, visit the 2 Motor Gearbox - Through Bore (REV-21-2099) page to learn...

New and improved, the Mecanum Drivetrain Kit V2 gives teams all the parts needed to build a Mecanum Drivetrain for use within robotics programs like FTC. This updated kit uses Ultra 90 Degree Gearboxes to place the UltraPlanetary HD Hex Motors within the...

The MK Battery ES17-12 is commonly used in FIRST Robotics Competition robots. Specifications Manufacturer: MK Battery Voltage: 12V Capacity: 18AH (20 Hour Rate) Product Dimensions: 7.13in x 2.99in x 6.57in Weight: 12.89lbs Documentation MK...

Dead Axle Tube is compatible with the REV ION System and can be used with 3/4in Needle Bearing Carrier (REV-21-2385) and MAXSpline Shaft (REV-21-2520) as the dead axle in a dead axle roller. Can also be used with custom rollers and as...

The 1in Pivot Joint is compatible with the REV ION System. Create a pivot joint at the end of a piece of MAXTube - 1x1 with Grid Structure. Specifications Material: POM (Acetal/Delrin) Documentation REV ION Build System Documentation Introduction...

The MAXSpline Shaft is compatible with the REV ION System. The shaft is an extruded aluminum MAXSpline that provides a high strength alternative to 1/2in hex shaft that can interface with any REV ION System components with a MAXSpline bore. The...

The REV Robotics Analog Pressure Sensor is a 5V sensor that can measure pressures up to 200 PSI. It outputs an analog voltage that is proportional to the measured pressure and can plug directly into the roboRIO or the More Board V2.0...

The WAGO 221 Inline Splicing Connector is a robust and easy to use splicing connector that makes fiddling with hard-to-master crimp-style connectors a thing of the past. Simply lift the lever up, insert the stripped wire, and push the lever back down to...

The REV Mini Power Module (MPM) is a compact power distribution module that allows you to securely and quickly power peripheral devices to your robot. Need more low-current channels on your PDH? Wire the MPM to one of the high-current channels on the PDH...

The MAXPlanetary 550 Input Kit gives users the ability to use 550 size motors with the MAXPlanetary System.  Features Does not require permanent modifications to the motor Press-fit shaft adapter avoids set screws that can come...

The MAXPlanetary 775 Input Kit gives users the ability to use 775 size motors (775pro or AM RedLine) with the MAXPlanetary System. Features Does not require permanent modifications to the motor Press-fit shaft adapter avoids set screws that...

The REV Driver Hub is a compact mobile computing device designed for interfacing with the Control Hub (REV-31-1595). The Driver Hub was designed and built as an easy to use, dependable, and durable device for use in classroom and the competition. It...

With over 180 parts, the EDU Kit V2 is specifically created to implement hands-on STEM projects in the classroom. This robotics kit is used to teach a variety of lessons ranging from computer programming and engineering principles to project management...

The M3 Hardware Bundle provides a multitude of hardware options that can be used within the 15mm Build System. The focus of the bundle is on compatibility with structural components like Extrusion and Brackets. Use this bundle to restock your...

The FTC Timing Belt and Pulley Bundle contains an assortment of components needed for a pulley-based motion transmission system. Timing Belts and Pulleys are lighter, more compact, and more efficient at transferring motion than chain and sprockets...

The 5mm Hex Shaft and Spacer Bundle features an assortment of REV products that work to transmit intended motion and constrain unintended motion in the DUO Build System. Use this bundle to restock your existing shaft and spacer supply, or as a great...

The FTC Cable Bundle offers a plethora of major cables and other accessories for a variety of robot design needs, without having to sacrifice wiring best practices. Necessary cables, like the XT30 Extension Cable, come in two different...

The M3 Standoff Bundle is perfect for raising one assembly above another or as linkages. Standoffs are also commonly used with REV C Channel to properly space the channel in order to allow chains or belts to fit inside. Use this bundle to...

The FTC Bearing Bundle offers a plethora of motion support components for the 15mm Build System. The basics of motion support can be found on the Supporting Motion documentation page. Use this bundle to restock your existing bearing supply, or as a...

The C Channel Bundle contains various lengths of 45mm x 15mm C Channel and is designed to work seamlessly with existing REV 15mm Extrusion. They can be used in locations where additional torsional strength is required. The 45mm wide side...

The U Channel Bundle contains multiple lengths of 45mm U Channel and is designed to work seamlessly with existing REV 15mm Extrusion. The U Channel Endcap and Tensioning Bushing allows users to fine tune their system when designing and...

The Servo Bundle is a one stop shop for getting up and running with the REV Smart Robot Servo. Included in this bundle are all the major electronic and structural accessories for programming, powering, and building using the Smart Robot Servo. Use...

The #25 Chain and Metal Sprocket Bundle can be used to change the speed, torque or direction of a motor. The REV 15mm Build System is designed around #25 Roller Chain using compatible #25 Sprockets. The bundle also includes the...

The 15mm Extrusion Lift Kit offers an assortment of components needed to build an un-powered 3-stage continuous or cascading lift. The basics of the linear motion kit can be found on the Introduction to Linear...

The FTC Sensor Bundle offers an assortment of REV Sensors and sensor accessories to help your robot understand the world around it. Use this bundle to restock your existing sensor supply, or as a great starting point for a new FTC team...

Tested for the rigors of competition, REV Mecanum Wheels are steel plates with rollers supported by ball bearings allowing for the perfect combination of wheel rigidity and roller movement. Included in the set of wheels are Universal Hex Adapter making...

The REV Robotics Control Hub is an affordable all-in-one educational robotics controller.  It provides students all the necessary interfaces for robotics and mechatronics projects with multiple programming language options. The Control Hub is...

Building on the robust foundation of the original SPARK, the SPARK MAX Motor Controller incorporates advanced brushed and brushless DC motor control in a small and easy-to-use package with PWM, CAN, and USB connectivity. Never before has an FRC...

Updated version of our popular Linear Motion Kit. This kit has been redesigned to be even easier for teams to use with REV 15mm Extrusion to create compact linear slides. New additions to the kit include End Cap pieces to keep lift stages in place,...

A custom-designed tool that allows teams to easily break and re-assemble #25 chain. The mandrel is used to push out the chain pin. If using master links, the pin can be completely removed, but the depth guide screw allows the option of partially pressing...

The SPARKmini Motor Controller is an inexpensive in-line brushed DC motor controller designed to offer the same performance characteristics as the Control Hub (REV-31-1595) or Expansion Hub (REV-31-1153) motor ports in a small 60mm x 22mm footprint...

Now legal for both FTC and FRC! Blinkin makes adding LEDs to your robot as simple as driving a motor. Chose the pattern you want and give it the corresponding PWM signal. The REV Robotics Blinkin LED Driver is a compact LED driver module that simplifies...

For smaller applications the REV Building System also comes in a 15mm x 15mm square extrusion. The slots are designed to fit standard M3 hardware rather than expensive t-nuts. This product is a 4-pack of 420mm pieces of extrusion, an appropriate...

Charger for use with our 12V Slim Battery. The output is wired with an XT30 male connector for charging. For the input, the battery charger has an IEC C13 power cord to standard, grounded, North America wall outlet plug (NEMA 5-15). *Do not...

Add this switch between your battery and Expansion Hub to have convenient on/off control of your robot. We recommend mounting the switch slightly recessed from the outside of your robot so that it's not accidentally turned off by another robot during a...

The REV Robotics Expansion Hub is a low-cost educational device that can communicate with any computer (commonly the REV Robotics Control Hub or an Android Phone) to provide the interfaces required for building robots and other mechatronics. The...