Shop All

This is all of the hardware included in the 15mm Linear Motion Kit V2 (REV-45-1507). Specifications Hole Diameter: M3 Clearance Kit Contents QTY 8 - M3 x 8mm Low Profile Socket Screws QTY 8 - M3 x 8mm Hex Cap Screws QTY 8 - M3 Nyloc Nuts QTY 8 - M3...

This 4-pin JST PH to 4-pin roboRIO I2C Cable is designed to connect REV I2C sensors, like the REV Color Sensor V3, to the I2C port on the NI roboRIO for use in the FIRST Robotics Competition. Each cable is approximately 36 inches long. This cable...

The JST PH 6-pin to 4 Channel PWM Cable allows for seamless connection of the Through Bore Encoder into the FRC control system (roboRIO).

The JST PH 6-pin to JST PH 4-pin Cable allows for seamless connection of the Through Bore Encoder to the dedicated encoder ports on the FTC Control System (Expansion Hub or Control Hub). Also allows for the HD Hex Motor to...

These plastic 15mm Extrusion Slot Covers are ideal for making any machine look great!  COLOR  SKU  Red  REV-41-1633  White  REV-41-1634  Blue  REV-41-1635  Yellow  REV-41-1636  Green...

The U Channel Endcap spans between the two sides of U Channel to provide holes on multiple surfaces to fasten additional components to. Also, using the endcap is a great way to strengthen longer sections of U Channel that are experiencing high loads...

These set screws have a pre-applied coating of nylon, helping them to stay in place under vibration. Use these with REV's standard Shaft Collars or new Slim Shaft Collars to never lose another shaft collar in a match! Specifications Material: Steel

Make driving linear motion easy with the 22 Tooth Plastic Right Angle Rack Gear. Mount the rack gear to a slot in either the REV DUO Extrusion or REV DUO Channel while using any of the REV DUO Plastic Gears to drive motion. Specifications Module: 0...

1in Extrusion is compatible with the REV ION System. It’s a 1in x 1in square extruded aluminum tube, with slots designed to fit standard #10 hardware rather than expensive t-nuts. Take your robot mechanisms to a new level of sleekness with the Black...

These SPARK PWM Cables have a JST-PH 4-pin connector on one end, and a 0.1in 3-pin female PWM connector on the other. They are designed to convert the SPARK MAX Motor Controller's PWM/CAN port to a standard 3-pin PWM port on a robot controller. The black...

Custom hinge system used to create compact, simple hinges using REV DUO 15mm Extrusion. Hinges come in left, right, and center pieces, and are attached together using standard M3 hardware. Specifications Hole Diameter: M3 clearance Hole Spacing:...

Reduce the number of USB disconnects between the Expansion Hub and your Robot Controller Phone with our USB Retention Mount. When used with the included right-angle USB cable, this mount provides a strong, reliable connection between the cable and the...

This Eye-to-Eye Turnbuckle is ideal for tensioning string, cordage, or cabling in linear motion applications. The welded eyes provide significantly more strength than bent eyes. Specifications Material: Steel Thread: M5 Retracted Length: 106mm +-...

Split Lock washer with a 3/8in inner diameter. Specifications Material: Zinc-plated Steel ID: 3/8in OD: 0.680in Thickness: 0.094in Documentation ION Build System Guide #10 Hardware Basics CAD & Drawings REV-29-1240 Drawing

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length measured from tip to underside of screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1-1/2in Documentation ION...

Steel hardware of the appropriate size to work with the ION Build System 1in Extrusion. Length includes the flat screw head. Specifications Material: 18-8 Stainless Steel Diameter & Thread: #10-32 Length: 1/2in Documentation ION Build System...

The 1in Inside Corner Bracket is designed to enable more construction strategies with the 1in Extrusion. Designed for #10 hardware, the mounting holes are on a 1in pitch that allows for the creation of complex joints by stacking with other 1in...

The 1in Extrusion Endcap Slide allows teams to create compact and robust multistage lifts when combined with the 1in Linear Motion Kit (REV-15-1189) and the 1in Extrusion (REV-21-1000). The slide tab is offset allowing stages to fully nest when collapsed...

The REV Punch Tube is designed to enable teams to rapidly prototype ideas and build robots without some of the constraints generally associated with extrusion based construction. When paired with our Metric Step Drill (REV-49-1455) and 1/8in or 3.2mm...

This metal ball bearing mount bracket is used with the REV DUO System 15mm Extrusion. Version 2 brackets offer many improvements over our previous metal brackets, including holes on an 8mm grid that is compatible with many other building systems. This...

The REV POE Injector Cable was specifically designed to address a common problem for many FRC teams with their wireless radios: intermittent power glitches. The wireless radios used in the last several FRC seasons can be powered either through a...

This 12V RGB LED Strip is compatible with the REV Blinkin LED Driver (REV-11-1105). Each LED on the strip is wired in parallel and actually contains three embedded LEDs; a red, green, and blue LED. Each color can be controlled separately to create any...

All the drills you need for FTC in one handy tool! Specifications Maximum material thickness: 3mm Tool material: High-Speed Steel Shank: 0.25in Hex 10 unique diameters 3, 4, 5, 6, 7, 8, 9, 10, 11, & 12 mm Hole Size Compatibility 3mm Clearance...

Use the Anderson Power Pole to 2-pin JST VH Adapter Cable to connect your existing motors to the REV Robotics Expansion Hub. Teams that already own and use the Anderson Powerpole Crimper may purchase JST VH 2-pin Motor Cables (REV-31-1413), cut cables in...

The REV Robotics Logic Level Converter is a circuit board which generates a 5V output from the 3.3V input and uses a MOSFET on each signal line to create a bidirectional communication appropriate for a variety of digital signals include I2C communication...

Cross over cable to convert the pin out from Modern Robotic's I2C sensors to work with the REV Robotics's Logic Level Converter. 

The MiniBot Hardware Kit is a fast robot build ideal for basic programming training. Add control system components (REV-31-1595 Control Hub, REV-31-1596 Driver Hub, REV-31-1302 12V Slim Battery) and let your programming skills grow.  Kit Contents...

Our Polyurethane Hollow Round Belting is perfect for your conveyor, and intake mechanisms. Use Barbs to assemble custom length belts. 

The Servo Shaft Adapter makes it possible to drive a 5mm hex shaft with any 25T output servo including the Smart Robot Servo. The adapter attaches to the servo spline like any common servo horn and accepts a 5mm hex shaft on the opposite end...

Extend the reach of your MXP port by using this 18" cable to reposition your boards where you need them. Fully compatible with all REV Robotics MXP accessory boards (More Board, Proto Board, & RIOduino) Specifications Keyed male and female...

The REV Robotics Digit is multi-use MXP board for interface with the roboRIO. It has four 12 segment displays, which can be used to show any letters or numbers. It also features an analog potentiometer and two momentary buttons. Teams can use the...

Eccentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. The hole is drilled off-center of the bearing axis so by rotating the bushing on its mounting bolt, the clearance between the wheel and track can...

This dual bearing plate holds two V-Groove Bearings (REV-29-1014) to create an easy linear motion system for the ION Build System 1in Extrusion (REV-21-1000). Using a combination of Concentric (REV-21-1030) and Eccentric (REV-21-1029) bushings, the user...

Concentric bushings are used to hold our V-Groove Bearings (REV-29-1014) for linear motion applications. Used in conjunction with our Eccentric Bushing (REV-21-1029), the user can adjust how tight or loose they would like to tune their linear...

REV Polycarbonate Sheets are lightweight, clear, and impact-resistant plastic sheets for robot construction, prototyping, covers, guards, sponsor panels, intake surfaces, funnels, and other custom mechanisms. Polycarbonate is durable while still allowing...

The JST PH 6-pin Joiner Boards (REV-11-1277-PK4)  are intended to be used with the JST PH 6-pin Extension Cables to extend the reach of your NEO Brushless Motor sensor cables. The JST VH 2-pin Joiner Board - 4 Pack (REV-31-1429-PK4) are small...

The SPARK Flex Data Port Breakout Cable (REV-11-2853) breaks out the default pin functions of the SPARK Flex Data Port into commonly used connectors for external sensors. The keyed and locking Data Port connector ensures a secure and aligned fit when...

The USB-A to USB-C 2.0 Cable - 2m (REV-11-1232) is a longer version of the USB-A to USB-C cable included with the SPARK MAX Motor Controller and the Control Hub. Use this cable to connect your SPARK MAX or Control Hub to a standard computer from up to 2...

1.2mm UHMWPE Cord - 10M (REV-41-1162) is a high strength string for use with the small Pulley Bearings and the 15mm Linear Motion Kit to create a powered lift.   3mm UHMWPE Cord - 10m (REV-29-1244) is a high-strength and low-stretch...

The 8cm long Anderson Power Pole style connector to Female XT30 adapter cable (REV-31-1385-PK20) is used to covert team-modified battery connectors to the new XT30 connector.  Teams that already own and use the Anderson Powerpole Crimper may...